Power Your LED Lights With {Youyi} Factory's YY-D-300-5 110V/220V TypeB Switch Power Supply

A. Shock: 49m/s2(5G),11ms,once each X,Y and Z axis. B. Vibration: 10-55Hz,19.6m/s2(2G),20 minutes each along X,Y and Z axis.Input Electrical Characteristics

Project	YY-D-300-5
Output Power	300W
Input Voltage	110V Product: 100Vac～135Vac 220V Product: 200Vac～240Vac Switch by toggle the Settings switch inside the product
Input Voltage Range	110V Product:100 Vac ～135Vac 220V Product:180 Vac ～264Vac
Frequency range	47HZ~63HZ
Leakage Current	≤0.25ma, @220Vac
Maximum Input Current	4A
Inrush Current	≤60A, @220Vac
Efficiency(full load)	≥80%

The Derating Curve Of Environment Temperature

Output Short Circuit Protection

Output Voltage	Comments
5.0 Vdc	The power supply will stop working when the short circuit is triggered and it restart working after solving problem.

Output Over Load Protection

Output Voltage	Comments
5.0 Vdc	The power supply will stop working when the outputcurrent is more than 105～138% of rated current and it will restart working after solving problem.

Over Temperature Protection

Output Voltage	Comments
5.0 Vdc	The power supply will stop working when the temperature above the set value and it will restart working after solving problem.

Output Over Voltage Protection

Output Voltage	Comments
6.0 Vdc	The output will not exceed 6.0V when external factors trigger malfunction of output. That can avoid the damage to theloader of the power supply.

Dielectric Strength

Input To Output	50Hz 3000Vac Ac file test 1 minute，Leakage current≤5mA
Input To FG	50Hz 2000Vac Ac file test 1 minute，Leakage current≤5mA
Output To FG	50Hz 500Vac Ac file test 1 minute，Leakage current≤5mA

Insulation Resistance

Input To Output	DC 500V The minimum insulation resistance must be no less than 10MΩ(at room temperature)
Output To FG	DC 500V The minimum insulation resistance must be no less than 10MΩ (at room temperature)
Input To FG	DC 500V The minimum insulation resistance must be no less than 10MΩ(at room temperature)

Environment Temperature Working Temperature:-10℃～+60℃ If customer want the product to work at the environment of - 40℃,please indicate special requirement when customer order it. Storage Temperature:-40℃ ~ +70℃ Humidity Working Humidity: Relative humidity is from 15RH to 90RH. Storage Humidity: Relative humidity is from 15RH to 90RH. Altitude

Working Altitude: 0 to 3000m

Dimensions Outside dimension : L*W*H=220×117×32mmInput 110/220Vac

If customer want the product to work at the environment of - 40℃, please indicate special requirement when customer order it.

Output Voltage And Current Specification

Project	YY-D-300-5
Output Voltage	5.0V
Setting Accuracy （No load）	±0.05V
Output Rated Current	60A
Peak Current	65A
Line Regulation	±0.5%
Load Regulation	LOAD≤ 70%：±1%（Amount to：±0.05V）V LOAD＞ 70%：±2%（Amount to：±0.1V）V

Startup Delay Time

Delay Time	220Vac Intput @ -40～-5℃	220Vac Intput @ ≥25℃
Output Voltage：5.0 Vdc	≤6S	≤3S
-	-	-

Output Dynamic Response

Output Voltage	Change Rate	Voltage Range	Load Change
5.0 Vdc	1～1.5A/uS	≤±5%	@Min.to 50% load and 50% to max load
-	-	-	@Min.to 50% load and 50% to max load

Output Voltage Rise Time

Output Voltage	220Vac input & full load	Note
5.0 Vdc	≤50mS	The rise time is when voltages rise from 10% to 90% .

Output Ripple & Noise

Output Voltage	Ripple & Noise
5.0 Vdc	140mVp-p@25℃
5.0 Vdc	240mVp-p@-25℃

Measure Methods A. Ripple & Noise test：Ripple & Noise bandwidth is set to 20mHZ. B. Connect a 0.1uf Ceramic Capacitor with a 10uf Electrolytic Capacitor parallel to output terminals to test Ripple & Noise.Fan Cooling Specific Cautions A. The product should be suspended in air or installed on the face of metal when it is assembled, and be avoided to place on the face of non-conducting heat materials such as, plastics, board and so on. B. The space between each module should be exceeded 5cm in order to avoid affecting cooling of power supply.The MTBF shall be at least 50,000 hours at 25℃ at the condition of full loading.The image below is top view of product and left side is terminal block. The power supply is built-in a switch can be toggled by a screw in order to change the input voltage to 110Vac or 220Vac (The value that shows in switch is the input voltage which have been sett ed).Attention: The power supply will be damage when the input voltage have been setted to 110Vac and the real input voltage is more than 150Vac.Unit:mmTable 1 : Input 5 pin terminal block (pitch 9.5mm)

Name	Function
L L	The AC Input Line L
N N	The AC Input Line N
	Earth Line

Table 2 ：Output 6 pin terminal block （pitch 9.5mm）

Current conducted through the output terminal block should not exceed 20A, so do not overload test and work at that condition. Or the terminal block will be damaged from high temperature.

Name	Function
V+ V+ V+	Output DC positive pole
V- V- V-	Output DC negative pole

Method 1: M3 Screws are suitable for 4 tapped holes in the bottom of the shell.

The power supply must work at the condition of insulation and make sure the terminal post of cable is insulation. Besides, make sure the product is grounded well and forbid touching the cabinet to avoid scalding hand.

Youyi YY-D-300-5 110V/220V TypeB Code Switch 5V 60A LED Power Supply

Products Details

Featured Products

Contact us