Factory Direct Youyi YY-D-200-5 G-Series 5V 40A LED Power Supply For Reliable Performance

A. Shock: 49m/s2(5G),11ms,once each X,Y and Z axis. B. Vibration: 10-55Hz,19.6m/s2(2G),20 minutes each along X,Y and Z axis.Input Electrical Characteristics

Project	YY-D-200-5 G Series
Normal output power	200W
Normal voltage range	200 Vac ~240Vac
Input voltage range	176Vac ~264Vac
Frequency range	47HZ~63HZ
Leakage Current	≤0.25ma,@220Vac
Max input AC current	2A
Inrush current	≤35A，@220VAC
Efficiency(full load)	≥87%

Operate temperature rating CurveOutput Short Circuit Protection

Output Voltage	Comments
5.0 Vdc	Output will be stopped when the circuit is shorted and restart operating after eliminating malfunction.

Output Over Load Protection

Output Voltage	Comments
5.0 Vdc	Output will stop working when the output current is more than 105～138% of rated current and it will restart working after eliminating malfunction.

Over Temperature Protection

Output Voltage	Comments
5 Vdc	The power supply will stop working when the temperature above the set value and it will restart working after solving problem.

Dielectric Strength

Input To Output	50Hz 3000Vac Ac file test 1 minute，Leakage current≤5mA
Input To FG	50Hz 2000Vac Ac file test 1 minute，Leakage current≤5mA
Output To FG	50Hz 500Vac Ac file test 1 minute，Leakage current≤5mA

Insulation Resistance

Input To Output	DC 500V The minimum insulation resistance must be no less than 10MΩ(at room temperature)
Output To FG	DC 500V The minimum insulation resistance must be no less than 10MΩ (at room temperature)
Input To FG	DC 500V The minimum insulation resistance must be no less than 10MΩ(at room temperature)

Environment Temperature Working Temperature:-10℃～+60℃

Products are able to start and work at -40℃. If the product has long been working at the environment - 40℃, please indicate your special request.

Storage Temperature:-40℃ ~ +70℃ Humidity Working Humidity: Relative humidity is from 15RH to 90RH. Storage Humidity: Relative humidity is from 15RH to 90RH. Altitude

Working Altitude: 0 to 3000m

Dimensions Outside dimension : L*W*H=190×82×30mm

Operate voltage rating Cuidline

If customer want the product to work at the environment of - 40℃, please indicate special requirement when customer order it.

Output Voltage And Current Regulation

Project	YY-D-200-5
Output Voltage	5.0V
Setting Accuracy （No load）	±0.05V
Output Rated Current	40A
Peak Current	42A
Line Regulation	±0.5%
Load Regulation	Load≤70：±1%（Amount to：±0.05V）V Load＞70：±2%（Amount to：±0.1V）V

Startup Delay Time

Delay Time	220Vac Input @ -40～-5℃	220Vac Input @ ≥25℃
Output Voltage：5.0 Vdc	≤6S	≤3S
-	-	-

Output Dynamic Response

Output Voltage	Change Rate	Voltage Range	Load Change
5.0 Vdc	1～1.5A/uS	≤±5%	@Min.to 50% load and 50% to max load
-	-	-	@Min.to 50% load and 50% to max load

DC Output Voltage Rise Time

Output Voltage	220Vac input & full load	Note
5.0 Vdc	≤50mS	The rise time is when voltages rise from 10% to 90%.

DC Output Ripple & Noise

Output Voltage	Ripple & Noise
5.0 Vdc	140mVp-p@25℃
5.0 Vdc	240mVp-p@-25℃

Measure Methods A. Ripple & Noise test：Ripple & Noise bandwidth is set to 20mHZ. B. Use a 0.1uf ceramic capacitor in parallel with a 10uf electrolytic capacitor at output connector terminals for ripple & noise measurements. Fan cooling

Specific Cautions A. The product should be suspended in air or installed on the face of metal when it is assembled, and be avoided to place on the face of non-conducting heat materials such as, plastics, board and so on. B. The space between each module should be exceeded 5cm in order to avoid affecting cooling of power supply.The MTBF shall be at least 50,000 hours at 25℃ at the condition of full loading.Table 1 : Input 5 pin terminal block (pitch 9.5mm)

Name	Function
L L	The AC Input Line L
N N	The AC Input Line N
	Earth Line

Table 2 ：Output 6 pin terminal block （pitch 9.5mm）

Name	Function
V+ V+ V+	Output DC positive pole
V- V- V-	Output DC negative pole

Current through the output terminal block should not exceed 10A, so never overload test and work in that kind of condition. Or the terminal block will be damaged because of high temperature.

The power supply must work at the condition of insulation and make sure the terminal post of cable is insulation. Besides, make sure the product is grounded well and forbid touching the cabinet to avoid scalding hand.

The figure below is mounting hole position

Method 1. M3 Screws are suitable for 4 tapped holes in the bottom of the shell. The length of screw that is fixed into the power supply must not exceed 3mm. Method 2. M3 screws lock in the mounting rack of 3 U grooves under the cabinet.

One way should be chosen from the two methods, make sure that the part of screw that is in the body of power supply should be less than 3mm and exert not much strength to avoid damaging the screw.

The figure below is vertical view of product, Input 5 pin terminal block is on the left side and Output 6 pin terminal block is on the right side.

Youyi YY-D-200-5 G-Series 5V 40A LED Power Supply

Products Details

Featured Products

Contact us